![]() ![]() When dealing with any kind of drywall anchor that requires pre-drilling, you really only need to worry about a couple of things. How Deep to Drill Pilot Holes for Drywall Anchors Pay attention to the back of the packaging, and pick up the best drill bit at the store when you get the drywall anchors. For self-tap drywall anchors, you can forgo the drill bit altogether. For our recommended Snaptoggle and FlipToggle anchors, a 1/2-inch drill bit is needed. The great thing about drywall anchors is they pretty much tell you exactly what size hole to drill. What Size Pilot Hole is Best for Drywall Anchors? When the toggle clears the backside of the drywall, it will open up and grip the wall. Squeeze the toggle closed and jam both the toggle and bolt through the wall.Then, thread the toggle onto the bolt with the tips facing the screw head. Put the bolt through the bracket you’ll be attaching to the wall.The manufacturer instructions on the side of the box of toggle bolts should give you the necessary specs for drill bit widths. Drill a hole big enough to allow for the toggle bolt to slip through when in its folded position.Also, while these drywall anchors can support a fair amount of weight, your softish drywall will fail if you put too much weight on it. This will require a hole that exceeds the width of the screw head, so toggle bolts can really only be used in conjunction with a bracket that will cover the hole. For one thing, you’ll have to drill a hole that allows for the toggles to pass through. Of course, there are a few things to be aware of before getting started. When you’ve got heavier items to hang, but can’t find a wall stud to hang it on, toggle bolt anchors can save the day. Once you tighten down the molly bolt, back the screw out of the sleeve and hang directly from the head of the screw.This will cause the legs to expand out and grip the other side of the drywall. After insertion, tighten the bolt in the sleeve of the molly.Check the package to find out the size you’ll need for the pilot hole. Mark the point where you’d like to hang stuff. ![]() You can use a drill, but go slow so you don’t overdrive it. A rubber mallet is best, but a small finish nailer will also work. Stick the anchor in the pilot hole and tap it into place until the head of the anchor flushes up with the wall.If a pilot bit doesn’t come with the set, the packaging will tell you which size to use. You can use any variety of tools to accomplish this, though you need to make the pilot hole smaller than the width of the anchor. With a pencil, mark the point where you want to hang whatever it is you’re trying to hang.How to Use a Drywall Anchor Installing A Plastic Sleeve Anchor ![]() Use these with discretion and test them prior to hanging expensive items from them. There are some drywall anchors rated for 100 pounds or more. Over 50 lbs: Snaptoggle, toggle bolts, or screw into an actual stud.25 to 50 lbs: Snaptoggle, molly bolts, or traditional toggle bolts.10 to 25 lbs: self-drilling threaded drywall anchors.Less than 10 lbs: plastic sleeve anchor.For the sake of brevity, we’ll stick with some of the more common types. While there are actually many types of drywall anchors available, some are more common than others. I would do it all again.Generally, your drywall anchor selection will revolve around the weight of the item you wish to hang. I was really happy with the way this turned out and the clients were really happy with how it came out. ![]() What I’ll never do again: “I don’t know, because I want to do it again! I have been pushing to do some more concrete looks in other places for other projects. This was more or less $1,200 and, because they’re pre-cut, the install was around $1,000. “In order to achieve that look, we didn’t want to buy a slab because that’s going to cost $2,000. “I don’t think most people understand sometimes that with slabs you can either get a slab at a slab yard, or you can get a prefabricated countertop.” In this particular design, a slab would have cost $2,000, and installation of it would have cost another $2,000. Sneakiest save: “The countertops,” Hayslett says without hesitation. We got the brass, which looks really special in there, but brass costs a lot more than if you get chrome or something like that.” “We wanted something really sleek and modern. Most insane splurge: “I would say the plumbing fixtures were a splurge,” Hayslett says, noting that the choice of brass fixtures was influenced by the way brass interacted with the color of the stucco walls. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |